Since I bought the iPhone 8, I have always been curious about the wireless charging function of the iPhone 8. Although it is an increasingly mature qi standard, as Apple's first mobile phone to support wireless charging, there is still a little expectation.
Belkin charging board, Apple official price 498 soft brother
One of the official brands of Apple's official website, orders placed on Apple's official website, and with the three-period interest-free move for China Merchants Bank, the requirements for wireless charging are small, because they have just finished buying the pd's fast charge and type-c lines, but they are facing wireless. The temptation to charge is still to bow to Apple
Out of the box
Shunfeng
As always, it is wrapped in plastic sheets on the board, which is very firm and worth learning by other manufacturers.
Appearance list
Applicable equipment
Various information
The bottom can be pulled open
real body
Family portrait
Like a bowl
Thickness is not too large
The back of the gray part is non-slip rubber
Power port close-up
Power adapter information
Good fit between power cord and charging board
The diameter is about 120mm
Charge ~
Basically, it must be placed in the middle of the charging pad to be charged smoothly, but it cannot be easily placed on it (how lazy I am)
That does not work
This will not work
Of course, the above picture is somewhat exaggerated, in fact, as long as the phone can be smoothly charged in the middle of the slip ring
2. About anti-slip This point I think the charging board is still good, under the official set and the anti-skid ring under the blessing, the charging board can be tilted to a certain extent, do not slide the iPhone
Tilt~
This began to slowly slide down
For streaking classmates, the protection of the glass is certainly not as good as rubber, so it can only be slightly tilted and does not fall
However, for the charging board, we must be sure to use it on a flat table, so the anti-slip property is a bit nitpicking here.
3. About charging speedWe are most concerned about the charging speed, Apple's official data is 7.5W, faster than the original 5W limited.
In the actual measurement, because the measurement can only be performed during the lunch break, there is no waiting for the battery to be full. The measured result is that the electricity from 28% to 52% for a total of 30 minutes, the performance is pretty good
The heat control is also very good, the phone is slightly warm, the charger plate adapter no obvious heating 
The answer given by Belkin's official is that a 3mm protective sleeve can be charged, but the measured results are not
The result is: penetrating power! do not! Strong!
There are pictures and the truth:
Protective Case + Bank of China Brochure
Protective cover + printed ppt
The words of the three together: Continued
How thick is that ppt, and it's about 4mm after pinching:
The classmate happens to have a charging board for IKEA. The price is about 250 yuan. Personally think that the front face value is higher than that of Belkin, but the details are still not as good as Belkin. (The reason is expensive.)
Picture here:
Exterior
Comes with a 10W charging port
Cable is not removable
Charging board parameters
Adapter information
thickness
Charging speed certainly not as fast as Belkin, and the heat is greater than Belkin, after all, the price in this, can only say that the price is very good
to sum upWireless charging greatly enhances the convenience of our charging. It will never happen in the dark. It is suitable for placing the charging board on the bed! Head! Cabinet! Pia ji put, you can bury your head and sleep, the only line charge is not, can not charge while holding the phone to play, so when the usual charge, or recommend the ordinary line charge, convenient (iPhone8 supports PD fast charge, The speed is much faster than the charging board).
188+99
So generally I still use my pd fast charging combination during the day and only put it on the charging board while sleeping (because our school is off at 11pm).
Incremental encoders provide speed, direction and relative position feedback by generating a stream of binary pulses proportional to the rotation of a motor or driven shaft. Lander offers both optical and magnetic incremental encoders in 4 mounting options: shafted with coupling, hollow-shaft, hub-shaft or bearingless. Single channel incremental encoders can measure speed which dual channel or quadrature encoders (AB) can interpret direction based on the phase relationship between the 2 channels. Indexed quadrature encoders (ABZ) are also available for homing location are startup.
Incremental Encoder,6Mm Solid Shaft Encoder,Hollow Rotary Encoder,Elevator Door Encoder
Jilin Lander Intelligent Technology Co., Ltd , https://www.jllandertech.com